Kayden CLASSIC® 830 Flow Switch & Transmitter

• CRN - Canadian Registration Number - The Kayden Classic 830 does not have a CRN Number

  
  

• CSA - Local (Sensor) Enclosure
  • Flameproof: Class I, Division 1, Groups B, C and D; Ex d IIB + H2
  • AEx d IIB + H2 (Class I, Zone 1, Group IIB + H2)
  • Temperature Code: T3
  • Enclosure Type 4 / IP55
  • Single Seal Approved per ANSI / ISA 12.27.01-2003
• CSA - Remote Electronics Enclosure - Optional
  • Flameproof: Class I, Groups B, C and D; Ex d IIB + H2
  • AEx d IIB + H2 (Class I, Zone 1, Groups IIB + H2)
  • Temperature Code: T3
• FM - Local (Sensor) Enclosure
  • Flameproof: Class I, Division 1, Groups B, C and D
  • Temperature Codes: T2D (Ta=75º C); T3 (Ta=65º C)
  • Class I, Zone 1, AEx d IIB + H2
  • Enclosure Type 4 / IP55
• FM - Remote Electronics Enclosure - Optional
  • Flameproof: Class I, Division 1, Groups B, C and D
  • Temperature Codes: T2D (Ta=75º C), T3 (Ta=65º C)
  • Class I, Zone 1, AEx d IIB + H2
  • Enclosure Type 4 / IP55

• Thermal (Calorimetric)

• NEMA 4 / IP55

• Threaded Style: Maximum Available Working Pressure to psig: 3,500 (bar: 241.3, MPa: 24)

• Horizontal
• Vertical

• -55° to 65° C (-67° to 149° F)

• -45° to 200° C (-50° to 392° F)

• Product should be stored in a clean and dry environment between -30° and 60° C (-22° and 140° F)

• Flow Service:
  ±1.0% of Set Point over Operating Range of ±28° C (50° F)
• Level Service:
  ±0.64 cm (0.25")

• Gases:
  0.6 to 20,000 cc/second
  Standard Condition: 20° C (70° F) at 14.7 psi (1 atm)
• Hydrocarbon-based Liquids:
  0.035 to 110 cc/second
• Water-based Liquids:
  0.015 to 50 cc/second

• Approximately 0.5 to 30 Seconds

• 3/4" Female NPT

• Not Required
• Type 1; 0.180" Bore, 316 Stainless Steel
• Type 2; .086" Bore; 316 Stainless Steel

• 1/4" Threaded

• In-Line body length is 3.5" (8.8 cm)

• 2 SPDT sealed relay contacts rated @ 4 amps resistive 230 VAC or 30 VDC Max, individually adjustable

• 12-24 Vdc; 120-240 Vac, 50-60 Hz
• Power Consumption: Maximum 4.8 W (Fully Configured)
• Universal Power Input

• MODBUS RTU Communication-Alarms, Flow Status and Diagnostics
• RS-485 using Kayden's Remote Control and Monitoring Software (RCMS) or other Modbus Compatible Software

• 4-20 mA (Thermal Signal, Scaleable)

• Adjust Relay Modes
• Adjust Set Points 1 and 2
• Load or Save User Settings
• Lock or Unlock the Display Panel to Protect the Settings
• Many other Adjustable Features
• Modify Heater Settings to Optimize Response Time
• Monitor Operating Status
• Operated via a Personal Computer Locally or from a Remote Control Center
• Visualize the Actions of the Process via the Graphical Display

• * Only configurable from the Kayden RCM software
• 100% Digital Design. Electronics are Environmentally Sealed
• 4-Adjustable Independent Switch Point Timers
• Automated Redundant Self-Test Diagnostics
• Display Panel Lock-Out*
• Easy Setup: No Mechanical Jumpers or Trim Pots
• Incrementally Adjustable Heater Power (5% steps) with Automatic Over-Range Protection
• Intelligent User Interface with Push-Button and Constant Display of Operation (Flow/Level)
• Start-Up Bypass Timer
• Temperature Compensation
• Temperature Mode*: Process Temperature may be Displayed/Graphed in Flow/Level Mode

• Copper-Free Aluminum (Does not exceed 0.4% Copper)

• Powder Coated Polyester TGIC

• 1" Female NPT Conduit Connection
• Buna-N O-Ring on Cover

• Blind Cover - Flameproof
• Glass Lens Cover - Flameproof

• 316/316L Stainless Steel with Nickel Brazing

• Blind Cover - Flameproof
• Glass Lens Cover - Flameproof

• InLine

• Flow

Kayden sensors incorporate two thin-film platinum Resistance Temperature Detectors (RTDs) and a separate heater element. The Reference RTD senses the actual process condition (as temperature). Heat is applied to the Active RTD by the heater element which is controlled by the microprocessor.

The microprocessor makes continuous comparisons between the temperature readings from the Reference RTD and the Active RTD (values stored as a result of setup programming). As process conditions change, for example increased velocity in a flow application, the Reference RTD “senses” the change and the microprocessor adjusts the heater and changes the relay state if required.

The CLASSIC 800 can be setup with a narrow range to detect very low flows or very small changes in the process, or with a wider range to ignore small fluctuations.

The CLASSIC 800 series switches and transmitters are digital devices and will not require calibration. By design they cannot drift or change in any way unless they suffer physical damage. After correct setup, the CLASSIC 800 will be stable and repeatable under stable process conditions.

The CLASSIC 800 may be setup in the field by the user for flow, level or interface with air, gases, liquids or slurries. The CLASSIC 800 may be setup to display process temperature through the RCM Software while functioning as a flow, level or interface switch/transmitter.